• +38 06236 3-3822
  • azmk@azmk.dn.ua

3D - TOUR FOR THE PRODUCTION OF METAL STRUCTURES IN FULL CYCLE

OUR PRODUCTION

1

TOWERS MADE OF THE MULTISIDED BENT STRUTS

Power transmission line tower made of the multisided bent struts is the tapered tube of polyhedral cross-section fabricated by the steel sheet bending with the subsequent welding or fastening of its edges at rib or side. Rolled steel sheet is material for MSS making. Tower struts are fabricated with the height-varying cross-section, and tower consists of multiple separate sections (section length of about 12 m). Such towers feature very important property — versatility, i.e., adaptive capability at development of these various modifications. Advantages may include erection rate; such supports offer twofold and even fourfold advantage over the conventional towers. In terms of reliability, advantages are long service life, repairability and “vandal-proofness”. Towers require much less footprint as compared with wide-base lattice structures.

READ MORE
2

STEEL SUPPORT of TRELLISED TYPE of OVERHEAD POWER TRANSMISSION LINES of VL of 35 - 500 kV

This type of support are made according to drawings of engineering office of plant and the unified drawings of the project organizations.
— designs of these support are the national teams on bolts, practically without welded nodes;
— design features and engineering procedures which are used in case of their production provide high quality and reliability;
— reducing standard sizes of details and elements of support, reduces cost and facilitates transportation, warehousing and installation on building sites.
TYPES:
— support for VL 35 of kV;
— support for VL 110 of kV;
— support for VL 220 of kV;
— support for VL 330 of kV;
— support for VL 500 of kV;
— support for VL 750 of kV.

READ MORE
3

HOT GALVANISING OF METAL STRUCTURES

Hot-dip galvanizing is the process where galvanized products are manufactured by dipping into the bath of molten zinc. Before the hot-dip galvanizing, following operations are carried out: chemical pretreatment of fabricated metal products in degreasing tanks for the subsequent etching in hydrochloric acid solutions, treatment in flux tank, preheating and drying of products to be galvanized. A thickness of such coating ranges from 70 to 120mm according to requirement. Advantages of this coating are obvious, since it provides product anti-rust protection and improves some its characteristics, of which most obvious are aesthetic appearance and higher wear resistance enhancing its chemical and mechanical stability limits.
Service life of galvanized products constitutes 30-50 years!

READ MORE
4

STEEL MASTS AND TOWERS UP TO 120 m HIGH

In order to install radio communication lines, the plant jointly with the specialized institutes designed, manufactured and put into operation antenna stands and radio masts intended for use in the radio-relay communications lines with installation of various type antennas (television, cellular, etc.), as well as searchlight towers and various modification towers. Towers of radio-relay and cellular communications are manufactured as per the standard design developed by the Ukrainian Division of the USSR Ministry of Energy in Kharkov “Energosetproekt”. In addition, PJSC Avdiyivsky Metal Construction Details Plant will manufacture communications masts of any type and any complexity according to the customer’s drawings with in-house development of detailed SST drawings. Following materials could be used as corrosion-resistant coating of mast component: primer, enamel, hot-dip galvanizing or any other coating as may be agreed with customer.

READ MORE
5

METAL STRUCTURES ON THE REINFORCED CONCRETE POLES of 0,38 - 10 kV and 35 - 500 kV

Are held for use on the centrifuge the conic and vibrated steel concrete racks and support: intermediate, anchor and angular, trailer, one-chain and two-chain. The plant makes all range of a metal constructions for steel concrete support including traverses, headstalls, caps, collars, couplers, delays, bolts, arms and so forth.
This type of products has distinctive feature which consists that for connection of probes to a metalwork the stamping method, but not weldings is used that positively affects quality of connection and anticorrosive stability.

READ MORE
6

CIVIL AND INDUSTRIAL CONSTRUCTION

— a metalwork for gas flues;
— electrocable platforms;
— support under pipelines;
— compensators (various standard sizes);
— reservoirs, banks, reservoirs, cyclones;
— platforms, ladders, barriers of platforms and ladders;
— cooler metalwork;
— metalwork of frameworks of plant and civil buildings and constructions, bridge building: colons, farms, beams, communications, crossbar, runs and so forth;
— mortgage spherical and saddle steel washer.
Products are made according to drawings of design office of plant, drawings of the project organizations and for individual projects of customers of any complexity.
Depending on purpose of the metalwork and hardware issued by plant for anticorrosive protection engineering procedures of soil and integumentary coloring, if necessary – hot galvanizing are used.

READ MORE

PRODUCT CATALOG PJSC «AMCDP»

© Copyright 2016 PAO AMCDP Website creation Web Love Me